cufflinks

Dry-type surface cleaning of the laser camera. Turn off the equipment. Disconnect the power plug from the outlet. Wipe the surface clean, soft, damp cloth. If needed, use the right amount of soapy water or detergent cleaning, but do not use ammonia-based cleaners. When cleaning, be careful, do not make any liquid into the power line side El inflow inside the camera; plug in the power and turn the unit on. The cleaning of the laser head. Turn off the power; to open the device in accordance with the camera manual; use a small amount of ethanol soaked lint-free cloth and gently wipe along the same direction, not to lift the cloth, do not put any pressure on the laser head, so as not to cause damage; installed equipment on the power. The green laser pointer is the brightest laser pointer.
Laser camera card laser camera occur card, usually the fault tips: Film Jam,. Card film caused many reasons. Such as: film input tray can not send the piece drive shaft axis ask the friction force does not match the sensor failure, a sudden power outage. Therefore, require careful analysis, to accurately determine the card position, the right medicine, clear the film was stuck. If P921 of error difficult to determine when the failure occurred, 17INCH direction of the film there will be a bright, white line. The finalization of the problem in the software aspects of DRE systems, SECURELI NK connected with the 8150 machine to do a system the RESTORE solve this fault. It is among all kinds of laser pointer.
Kodak 8100 Dry Laser camera to malfunction, repair two cases. After the boot of the failure phenomenon can not be self-test or through self-test after the film seized the arm can not be seized film from the film cartridge. Display the fault code: S04 the Stopped: P121 the Printer Error; P116 the Pickup Fail. Turn the camera on the back cover Analysis and Troubleshooting. Manual door control switch is closed. The seizure arm seizure action. Film to achieve the film feed axis. But can not enter the film to feed the region, along the drive shaft to fall back to the film cartridge, and then the machine stops working, the phenomenon of the failure to occur and the error code. Able to seize the film. May exclude the possibility of vacuum pump failure due to a larger workload. So the green laser pointer is widely used in many occasions.
The camera to film every day amount in more than 200. Therefore, the possibility of mechanical wear. Adjust the location of the film feed shaft, still above phenomena occur and then suction cup hanger removed. Found that the boom horizontal large gap to remove the crane track. Appropriate to tighten the bench vise, re-assembly debugging, and troubleshooting. Normal fault phenomenon machine. Print failure. Stop working. And the film cartridge can not be closed. Display the fault code: P117 Feed Nip the Open: P178 Rback Not Home: P177 Crtg the Close of Er. Analysis and elimination of this code can not be found on the random repair manual. Open the camera back. Manual door control switch is closed. Teaching baton is one of the most widely used applications of laser pointer. 300MW Laser
Visible seizure arm seizure action, the film can reach the film feed shaft. A film to enter the film to feed the region. Down to a film can not, and fall back to the film cartridge. Kodak sucker each draw two or more film in the fragmentation under the action of only one film feed shaft to enter the film feed area. The rest of the film fall back to the film cartridge. Analyze the causes fragmentation failure, the sorter is removed (using special tools such as no special tools to beware of the screws or screwdriver off the machine and increasing the workload). The examination revealed that the sorter has serious wear deformation of the urgent need to replace the sorter, but the manufacturer shipped at least 3 days. Branch only one camera. The teacher, lecturer, presenter and business personnel would like to choose laser pointer for the laser indication.
Lay-off the loss of three days too much careful study. Remove the film card box bottom. According to points. Film look like cutting a temporary slice. After a few assembly adjustments troubleshooting. Can continue to use, pending the arrival of the new accessories timely replacement KODAK DRYVIEW 8100 failure to repair one cases of failure phenomenon KODAK DRYVIEW 8100 print and slice one dry-type semiconductor laser camera, machine failure rate, to facilitate the work. A few days ago, suddenly self-test program into the warm up appears P551 error code. Especially the low power laser pointer is very practical. Zumba Fitness DVD
Failure Analysis: interpreted as a fault code analysis based on the laser camera, check the "Quick Reference Guide" included with the P551: imager is unable to The the print because the processor did not warm up. Laser camera "processor heater" did not reach the scheduled operational temperature, suspended the operating procedures, which can roughly determine the failure process can be judged. Heating drum failure; heating the interface between the drum and the motherboard circuit failure; motherboard failure. First analysis of the 8100 laser camera works, especially the principle of the heating drum work to make it clear, is no detailed information can only open the lid to find the heating drum. Someone would like to select laser pointer as the practical indicating tool.
A step by step and thus reverse the direction of progress, the analysis of the heating signal transmission line. Found that this heating signal by the motherboard via an interface circuit to control the heating drum. To open the interface circuit box, and found that a simple control circuit board which can be broadly analysis of heating signal transmitted by the motherboard over. So that K1 (relay), then the heating voltage 120VAc K2 (K1 control) added to the heating coil of the drum. The heating coil total of three groups, each group of resistance for 3012. Visit with a multimeter the resistance to normal. Open the side panel of the drum and found inside a coin-sized thermal protection switch, thermal protection, when the drum temperature is too high heating signal to disconnect the main drum asked. laser pointer can control the pagedown and pageup of the PPT document in the computer.